MELSERVO-J4

Options/Peripheral Equipment

Products on the Market for Servo Motors Contact the relevant manufacturers directly. When fabricating a cable with the following connectors, refer to the relevant manufacturers' instruction manuals for wiring and assembling procedures. Electromagnetic brake connector for HG-KR/HG-MR series Applicable servo motor Feature (Note 1) Connector (Japan Aviation Electronics Industry, Limited) Crimping tool (Japan Aviation Electronics Industry, Limited) Applicable cable example Rotary

Wire size: 0.3 mm 2 to 0.5 mm 2 (AWG 22 to 20) Cable OD: 3.6 mm to 4.8 mm Wire example: Fluorine resin wire (Vinyl jacket cable RMFES-A (CL3X) AWG 20, 2 cores Dyden Corporation (Note 3) or an equivalent product)

Plug: JN4FT02SJ1-R Socket contact: ST-TMH-S-C1B-100-(A534G)

HG-KR/ HG-MR

For contactor: CT170-14-TMH5B

IP65

Straight type Angle type

Electromagnetic brake connector for HG-SR/ HG-JR 3000 r/min series Rotary

Connector (DDK Ltd.)

Applicable cable example

Applicable servo motor Feature (Note 1)

Type Type of connection

Plug

Socket contact

Cable OD [mm]

CMV1-SP2S-S CMV1-SP2S-M1 CMV1-SP2S-M2 CMV1-SP2S-L CMV1S-SP2S-S CMV1S-SP2S-M1 CMV1S-SP2S-M2 CMV1S-SP2S-L CMV1-AP2S-S CMV1-AP2S-M1 CMV1-AP2S-M2 CMV1-AP2S-L CMV1S-AP2S-S CMV1S-AP2S-M1 CMV1S-AP2S-M2 CMV1S-AP2S-L

4.0 to 6.0 5.5 to 7.5 7.0 to 9.0 9.0 to 11.6 4.0 to 6.0 5.5 to 7.5 7.0 to 9.0 9.0 to 11.6 4.0 to 6.0 5.5 to 7.5 7.0 to 9.0 9.0 to 11.6 4.0 to 6.0 5.5 to 7.5 7.0 to 9.0 9.0 to 11.6

One-touch connection type

HG-SR/ HG-JR53B, 73B, 103B, 153B, 203B, 353B, 503B, 703B, 903B, 534B, 734B, 1034B, 1534B, 2034B, 3534B, 5034B, 7034B, 9034B

Straight

Screw type

Select from solder or press bonding type. (Refer to the table below.)

IP67

One-touch connection type

Angle

Screw type

Contact

Socket contact (DDK Ltd.)

Wire size (Note 2)

Solder type

CMV1-#22BSC-S2-100 CMV1-#22BSC-C3-100

1.25 mm 2 (AWG 16) or smaller

Press bonding type 0.5 mm 2 to 1.25 mm 2 (AWG 20 to 16) Crimping tool (357J-53164T) is required. Notes: 1. The IP rating indicated is for the connector's protection against ingress of dust and water when coupled to a servo amplifier/servo motor. If the IP rating of the servo amplifier/servo motor differs from that of these connectors, overall IP rating depends on the lowest of all. 2. The wire size shows wiring specification of the connector. Refer to "Selection Example in HIV Wires for Servo Motors" in this catalog for examples of wire size selection. 3. Contact Taisei Co., Ltd.

Rotary Rotary servo motor

Linear Linear servo motor

Direct Direct drive motor

5-29